FS Northern – Page 4 – Kongsi idea dan cara mudah setting router Unifi

Nak tanya Unifi FTTH boleh pasang/install alarm ker?

Jawapan ringkas dan mudah

Encik, nak kena tengok teknologi alarm apa yg pelanggan pakai.

Yang boleh, selalu alarm yang pakai auto dailing.

normally alarm guna DTMF feature.. utk unifi ada feature ini (sama macam DEL) -boleh rujuk vendor alarm dulu/check balik setting.

terima kasih

Configuration D-LINK DIR – 830M

Firmware version : V1.1.1

SETUP WIZARD

STEP 1: Open up a web browser and enter the default gateway’s IP address (192.168.0.1) in the Address\URL field.

STEP 2: Enter the username and password (admin/xxxxxxxx) according to device label

STEP 3: Click Login to log in to the Web page

This page will be shown by default for new device.

STEP 4: Click on Setup

STEP 5: Click on Next to Start Wizard.

STEP 6: Default mode is Gateway

STEP 7: Click Next to next step

STEP 8: Key in the PPP Username & Password

STEP 9: Click Next to continue

STEP 10: Click Next to continue

STEP 11: Maintain the default password configuration. (Password filled with current default random password according to device label)

STEP 12: Click Next to continue

STEP 13: Configure the 2.4 G and SSID and Password

STEP 14: Configure the 5 G and SSID and Password

STEP 15: Click Finished

Manual PPPoE Setup

STEP 1: Open up a web browser and enter the default gateway’s IP address (192.168.0.1) in the Address\URL field. STEP 2: Enter the username and password (admin/xxxxxxxx) according to device label STEP 3: Click Login to log in to the Web page STEP 4: Click TCP/IP STEP 5: Click WAN Setting STEP 6: Select WAN1 in Connection name STEP 7:Click IPv4 STEP 8: Select PPPoE STEP 9: Key in the PPP Username & Password STEP 10: Check to enable VLAN STEP 11: Fill in VLAN ID 500 STEP 12: Click Save & Apply the router to refresh

Configure Fiberhome SR – 1041Y

Look Firmware version : RP0100

STEP 1: Open up a web browser and enter the default gateway’s IP address (192.168.1.1) in the Address\URL field.

STEP 2: Enter the username and password (superadmin /f1ber@dm!n) according to device label

STEP 3: Click SIGN IN to log in to the Web page.

STEP 4: Click Advance Step

STEP 5: Click WAN Service

STEP 6: Select Connection name – 1_INTERNET_R_VID_500

STEP 7: Select Package Type: PPPoE

STEP 8: Select Mode: Route

STEP 9: Select IP Protocol Type: IPv4/ IPv6

STEP 10: Enable VLAN and enter VLAN ID 500

STEP 11: Select Service Type: INTERNET

STEP 12: Key in the PPP Username & Password

STEP 13: Select Dial Mode: Automatically

STEP 14: Select WAN Get IP Mode: PPPoE

STEP 15: Select Get IPv6 Prefix Mode: PrefixDelegation and Get IPv6 Address Mode: DHVPv6

STEP 16: Select Bound Ports: LAN 1,LAN 2, LAN 3, SSID 1 & SSID 6.

STEP 17: Click Apply to save config

STEP 18: *Reboot RG by power on off the device power button.

STEP 19: Select Status

STEP 20: Select WAN

STEP 21: Verify Connection Status: Connected

WiFi Configuration Setting

STEP 1: Open up a web browser and enter the default gateway’s IP address (192.168.1.1) in the Address\URL field.

STEP 2: Enter the username and password (superadmin /f1ber@dm!n) according to device label

STEP 3: Click SIGN IN to log in to the Web page

STEP 4: Select Basic Setup STEP 5: select WLAN STEP 6: Click Basic Config 2.4GHz STEP 7: Configure the SSID STEP 8: Click Apply to save the configuration. STEP 9: Repeat STEP 6 to STEP 6 for Basic Config 5GHz

STEP 10: Click Security Setting 2.4GHz STEP 11: Key In WPA Preshare key : password STEP 12: Click Apply to save the configuration STEP 13: Repeat STEP 10 to STEP 12 for Security Setting 5GHz