Category: Configuration RG

Configuration RG

How to Setup RG DLINK-825 Dynamic IP (manual)

 KLIK SINI UTK DEMO CARA-CARA CONFIG DLINK 825M

Setting up of DIR-825M Internet – Dynamic IP (manual)  pastikan latest firmware ver 1.1.8

Open up a web browser and enter the default gateway’s IP address (192.168.0.1)

in the Address\URL field

  1. Open up a web browser and enter the default gateway’s IP address (192.168.0.1) or

http://dlinkrouter.local./ in the Address\URL field.

  1. Enter the username and password (admin/****) {**** Please refer to the sticker at the bottom side of the RG}
  2. Click Login to log in to the Web page

 

 

  1. Click on the setting button to enter to the router  Setting.
  1. Click on the Operation Mode button to select router mode.
  2. Select ‘Gateway’ (Provided by your Internet Service Provider)
  1. Last, Click Save & Apply to save the configuration.

 

 

 

  1. Click on the WAN button to configure PPPoE account
  2. Select connect name – WAN1
  3. Select PPPoE
  4. Key in the PPP Username & Password
  5. Check to enable VLAN
  6. Fill in VLAN ID 500
  7. Last, Click Save to save the configuration

 

IPTV VLAN Setup

  1. Click Settings
  2. Click WAN
  3. Click Bridge VLAN
  4. Fill in VLAN ID 600 for IPTV
  5. Check Port LAN4
  6. Click Save & Apply the router to to save the Setting

 

Wireless Setup

 

  1. Choose (2.4GHz/5Ghz)
  2. Click Basic
  3. Untick the Disable Wireless LAN Interface.
  4. Select Country of Region – Malaysia
  5. Select AP Mode
  6. Fill in the SSID
  7. Click Apply Changes to Save the Setting

  1. Click Security Tab to configure
  1. Select Encryption type (Select WPA2 (AES) – recommended

10.Pre-Shared Key Format : Passphrase

  1. Key in Pre-Shared Key (wifi Password)

12. Click Save & Apply to save configure.

 

DNS Setup

  1. Click Security LAN to configure
  1. Click IPv4
  2. Click DNS
  3. Fill in DNS * 8.8.8.8
  4. Click Save & Apply the router to to save the Setting

 

PORT FORWARDING

  1. Click Features
  2. Click Port Forwarding
  3. Tick Enable Port Forwarding
  4. Fill in Local IP Add, .* Set 1 LAN IP
  5. Fill in Local Port Start, Local Port End * refer apps required eg: PS4
  6. Select Protocol TCP/UDP/Both
  7. Fill in Remote IP Address, Remote, *
  8. Fill in comment * name of apps
  9. Click Save & Apply the router to to save the Setting

 

SITE SURVEY (Wifi Analyzer)

This page provides tool to scan the wireless network. If any Router or IBSS is found, you could choose to connect it manually when client mode is enabled.

  1. Click Settings
  2. Click 2.4G Wifi tab
  3. Click Site Survey tab
  4. list of other wireless network appear * can use for channel selection to avoid interference

  1. Click Settings
  2. Click 2.4G Wifi tab
  3. Click Channel Number
  4. Change Channel Number * refer result from site survey.
  5. Click Save & Apply the router to to save the Setting

link untuk download firmware DLINK DIR-825 (ver 1.1.8 security update)

SETTING PORT FORWARDING RIGER ADM-206

 

STEP 1: Open your web browser and go to http://192.168.1.1

STEP 2: Enter the username and password (tmadmin/Adm@xxxx)

<Note: XXXX = last 4 digit of Mac Address>.

STEP 3: Click “Login” to log in to the Web page.

 

 STEP 4:To add new port forwarding service you can go to the “Advanced” and select the “Port Forwarding” to proceed the port forwarding setup. 

STEP 5:Click the “Add” button to key in the configuration detail.

STEP 6: Choose the “WAN Connection” type in the modem (in this page we use PPPOE setup). Select the predefined service according to designated port. If custom service is use; we need to define the service.

STEP 7: Select the “schedule” for the port forwarding. Key in the “Local LAN IP Address” of the affected service.

STEP 8:     Key in the information related to the service (“External Port Start to End” – “Protocol” – “Internal Port Start to End”).

STEP 9:  Click the “Apply” to save the configuration. 

STEP 10: Verify the Port Forwarding Setup. The added port should be working normally.

SETTING DNS RIGER ADM-206

 

STEP 1: Open your web browser and go to http://192.168.1.1

STEP 2: Enter the username and password (tmadmin/Adm@xxxx)

<Note: XXXX = last 4 digit of Mac Address>.

STEP 3: Click “Login” to log in to the Web page.

STEP 4: By default WPS is disabled. Go to the “Setup” button. Then select the “Internet Setup” and tick the “Manual Setup” to proceed security setting.

STEP 5: Click the “Security Setting” to configure security features of the Wireless LAN interface.

STEP 6: For WPS Wireless security mode, select “WPA2-PSK” to set as the Network Authentication.

 

  • Please take note that the Network Authentication both of WEP and WPA-PSK doesn’t support WPS function.

 

STEP 7: Choose the “Enabled WPS” to turn on the WPS setup.

STEP 8: Click the “Apply” to save the configuration.

 

STEP 9:       Go to Wireless Network Connection and “Select” the related “SSID Name” which already configure with WPS function.

STEP 10: A pop up message will show on your PC prompting to fill in password. Push the “WPS button” at the rear of the modem. After that the Wi-Fi connection will be establish. User can browse the internet.

SETTING FIX IP ADDRESS RIGER ADM-206

 

STEP 1: Open your web browser and go to http://192.168.1.1

STEP 2: Enter the username and password (tmadmin/Adm@xxxx)

 <Note: XXXX = last 4 digit of Mac Address>.

 STEP 3: Click “Login” to log in to the Web page.

STEP 4: Click on “Setup” and select “Internet Setup”. Then choose “Add “ to configure WAN interface.

STEP 5: Default in Modem is PPPOE mode with “(VPI : 0 / VCI : 35)”

STEP 6: Key in the modem “PPP Username” & “PPP Password “(Provided by your Internet Service Provider).

STEP 7: Tick the “Use static IP Address” for IPV4 and tick “Enable IP
Unnumber”

STEP 8: Key in the “Static IP Address” (Provided by TM) and “Subnet Mask”.

 

STEP 9: Click “Next” at the bottom of the page.

STEP 10: Last, Click “Apply” to save the configuration.

STEP 11: “WAN Setup” will show the summary of newly added PPPoE setting.

STEP 12: Click the “Status” and select “Device Info” to verify status Internet connection. When DSL is connected, ADM206-2 should be able to get the IP Address for Internet.

 

SETTING BRIDGE MODE RIGER ADM-206

ROUTER MODE CONNECTION – DYNAMIC IP

Pastikan modem RIGER ADM 206 berkeadaan baik

 

STEP 1: Open your web browser and go to http://192.168.1.1

STEP 2: Enter the username and password (tmadmin/Adm@xxxx)

<Note: XXXX = last 4 digit of Mac Address>.

STEP 3: Click “Login” to log in to the Web page.

 

STEP 4: Click on “Setup” and select “Internet Setup”. Then choose “Add” to configure WAN interface.

 

STEP 5: Default in Modem ATM PVC Configuration is “(VPI :0 / VCI :35)”

STEP 6: Choose and select connection type as below :-

•Protocol : BRIDGING.

•Encapsulation Mode : LLC/SNAP-BRIDGING.

STEP 7: Click “Next” to save the configuration.

 

STEP 8: Click “Apply” to save the configuration.

 

STEP 9: “WAN Setup” will show the summary of newly added Bridge setting.

 

STEP 10: Click the “Status” and select the “Device Info” to verify Bridge status connection.

STEP 11: Configure modem dialer on PC. Connect a RJ45 LAN cable from LAN Port modem to the LAN Port PC.

STEP 12: Open the dialer. Fill in your account “PPP username” and “PPP password”. Click on “Connect” button to proceed.

HOW TO SETTING MODEM RIGER ADM-206

 

ROUTER MODE CONNECTION – DYNAMIC IP

Pastikan modem RIGER ADM 206 berkeadaan baik

STEP 1: Open your web browser and go to http://192.168.1.1

STEP 2: Enter the username and password (tmadmin/Adm@xxxx)

<Note: XXXX = last 4 digit of Mac Address>.

STEP 3: Click “Login” to log in to the Web page.

 

Follow video youtube dibawah untuk step by step cara config modem RIGER ADM-206:

RECONFIGURE WIFI NETIS

 

How to configure your Wi-Fi

  1. Launch Web Browser and enter the default’s gateway’s IP address (192.168.1.1) in the address bar.
  2. Enter Username and Password. Username = tmadmin Password = Adm@xxxx (xxxx refers to last four digits of MAC address)

 

 

  1. Choose WLAN -> wlan0 (2.4GHz) Basic Setting, Enable 2.4GHz WLAN and configure the SSID.
  2. Untick the Disable WLAN Interface to enable Wireless.
  3. Fil in the SSID.
  4. Click Apply Changes to save the settings.

 

  1. Click Security tab to configure.
  2. Select Encryption type and Pre-Shared Key Format.
  3. Enter the Pre-Shared Key.
  4. Click Apply Changes to save configure.

 

  1. Choose WLAN -> wlan0 (5GHz) Basic Setting, Enable 5GHz WLAN and configure the SSID.
  2. Untick the Disable WLAN Interface to enable Wireless.
  3. Fil in the SSID.
  4. Click Apply Changes to save the settings.

 

 

  1. Click Security tab to configure.
  2. Select Encryption type and Pre-Shared Key Format.
  3. Enter the Pre-Shared Key.
  4. Click Apply Changes to save configure.

Tengok Password Guna Script

CARA-CARA NAK TENGOK PASSWORD UNIFI DALAM ROUTER ( BROWSER CHROME)

Step1 : Mula-mula, bawa cursor ke dalam kotak password dan klik mouse kanan. Klik pada Inspect

 

Step2 : Bawa cursor kedalam script, cari input type password.Delete perkataan password

 

Step3 : Bawa cursor kedalam kotak password. Anda sudah boleh nampak password yg ditanda …. tadi.

 

Step4 : Delete page script dengan klik Pangkah(X). Selesai.

 

 

MENU